wear resistant ceramic adhesiv > wearing ceramic tile bonding repair compound epoxy adhesive

wearing ceramic tile bonding repair compound epoxy adhesive

BD121 abrasion wearing resistant ceramic tile bonding repair compound epoxy adhesives

Performance feature of our BD121 anti abrasion wearing resistant repair epoxy ceramic tile adhesive：
1. It’s the two component adhesive compounded by modified toughening resin and special curing agent.
2. Aging resistant,with good water resistance,good toughness and high strength.
3. Can cure at room temperature,can also heat for curing

Product usage：
Used in the bonding of wearing abrasion resistant ceramic tile on the top surface and facade of the equipment.
With strong initial adhesion,high bonding strength,it won't fall off without using magnet or other support measures
during construction,optimizing construction technology and reducing construction cost.

Performance index：

Product name	physical state	Standard packing	operation time limit (25℃)	Curing time (25℃)	Range of application
anti wearing abrasion resistant ceramic tile bonding epoxy adhesive	paste	5kg	0.5h	12h	Used in the self-adhesion and each-adhesion between metal and ceramic etc materials.Especially used in the bonding of wear abrasion resistant ceramic chip/tile on the ceiling and facade of the equipment which suffers ash powder scour and material scour or erosive wear.

Item type	Color	Density (g/cm³)	Shear strength (Mpa) GB7124-2008	Impact strength (J/cm²) GB6328-1999	Tensile strength (Mpa) GB6329-2008	Compressive strength (Mpa) GB1041-2008	Working temperature （℃）
BD121	white	1.24	15	56	79	92	-60-150

How to use:
1.Surface treatment:
Clean up the dust,greasy dirt and rust on the surface of adherend,then grind or sand blast treatment,finally clean it by cleaning agent
and dry it by airing.

2.Configure ceramic tile bonding repair compound wearing abrasion resistant adhesive:
According to the specified requirement,make A and B components mix uniformly,the mass ratio A:B=4:1.When the temperature is low
in winter,can preheat the A component up to the temperature of 40-50 degree in advance for easy to mix using.

3.Using abrasion wearing resistant ceramic tile bonding repair epoxy compound:
Make the configured adhesive be coating on the adherend surface uniformly,then fold it,knock on it for once from the middle to
all around with rubber hammer,avoid the air getting into it.Double spread will get the better effect,under the premise of no shortage
adhesive,the adhesive layers are the thinner the better.

4.Curing:
Room temperature initial curing will take 4 hours,full curing will take 24 hours,when the temperature is low in winter,can heat it up
to the temperature of 80 degree slowly and keep this temperature for 2 hours after placing it for 2 hours.

Packing specification:
1.Common packaging: packed in a plastic drum,double components A component: 4Kg/drum, B component: 1Kg/drum,
12 drums/carton or 8 drums/carton.
2.We could offer professional customized packaging based on users' requirements.

Transportation storage:
1.Sealed storage in the cool and dry place.The warranty period is 12 months.
2.Avoid placing it upside down,knocking against and transporting it as a non-dangerous product during transportation.

Special version:
1.This parameter is for laboratory conditions,due to the actual working condition is more complex,suggest the users to do the
pretest according to actual working condition

2.When the environment temperature is below 15 degree,the curing time will prolong,should take proper heating measure

3.When the environment temperature is more than 25 degree or the mixing quantity is too large,the curing speed will expedite,
should properly shorten the application time of coating after mixing.

Construction protective measures：
1.Wear the protective masks,wear the protective glasses and rubber gloves
2.Need washing hands with soap before eating,drinking or smoking.
3.The health hazard after touching: a few people will have skin allergy phenomenon,see a doctor in time and avoid touching with
this product again.should wipe it with ethyl acetate when the sizing material paste on the skin by careless,then wash it with clear water.
Should wash it with clear water immediately and see a doctor when splashing into the eyes by careless.

Warm Prompt：
Residual adhesive solution cured products are non-toxic harmless organic solid,but maybe it will produce poisonous gas when
burning,non-professional personnel can not do combustion disposal,should be sent to garbage power plant or garbage burning
place treatment.

fire prevention measures：
Should choose dry powder to extinguish fire,can cover and flap it with dry powder,grit(the construction using abrasive) or
the non chemical fiber fabric when the sizing material catching fire.

Packaging actual photo of BD121 anti abrasion wearing resistant ceramic tile epoxy bonding adhesive:

------分隔线----------------------------